| Descriptions | Data Sheet | Instructions | MSDS | ||
|---|---|---|---|---|---|
| Descriptions | Data Sheet | Instructions | MSDS | ||
|---|---|---|---|---|---|
| ReactiveGel® Products | |||||
|---|---|---|---|---|---|
 |
|||||
|
• FORMULATED TO BE APPLIED TO COLD PIPES—VERY CREAMY • FOR USE ON ANY SYSTEM UP 250°F (121°C) • AMMONIA, BRINE, AND GLYCOL SYSTEMS, LNG, CRYOGENIC • FOR WELD PACKS ON PRE-INSULATED PIPE SYSTEMS • LOW PRESSURE STEAM (5.3# gauge pressure, 20# absolute pressure) • RG-2400 LT SPRAY Information Sheet (Click Here) |
|
|
|
|
|
 |
|||||
|
• FORMULATED TO BE APPLIED ON SYSTEMS UP TO 350°F (177°C) • FOR WELD PACKS ON PRE-INSULATED PIPE SYSTEMS • FOR USE ON ANY SYSTEM UP TO 350°F (177°C) • CAN TAKE 400°F (204°C) SHORT TIME SPIKES • LOW-HIGH PRESSURE STEAM (105.3# gauge pressure, 120# absolute pressure) |
|
|
|
||
 |
|||||
|
• ORIGINALLY FORMULATED FOR ARCTIC CONDITIONS • FOR USE ON HOT IN SERVICE PIPES UP TO 250°F(121°C) |
|
|
|
||
 |
|||||
|
• FORMULATED TO BE APPLIED TO CHILLED WATER SYSTEMS ONLY • OPERATING PIPING TEMPERATURE RANGE OF 40°F - 90°F (4°C - 32°C) |
|
|
|
|
|
 |
|||||
|
• TEMPERATURE RANGE UP TO 225°F (107°C) • FOR ALUMINUM PIPING SYSTEMS WITH MIC CORROSION POTENTIAL |
|
||||
 |
|||||
|
• CUSTOM DESIGNED CORROSION CONTROL FOR WELL CASINGS • FOR DISPLACING WATER IN WELLS WITH SERVICE UP TO 230°F (110°C) • MUST USE SPECIAL APPLICATION METHODS - A PUMPABLE PRODUCT |
|
|
|
|
|
 |
|||||
|
• CUSTOM DESIGNED CORROSION CONTROL ON STRUCTURAL STEEL • SPRAY ON APPLICATION WITH MINIMAL SURFACE PREPARATION • HARDENS OVER TIME; UV STABLE; ONE/TWO COAT SYSTEM • RED PRIMER AND GRAY TOPCOAT (CUSTOM COLORS) • DESIGNED AS AN EXTENDED LIFE PAINT TYPE COATING • COOLING TOWERS, PIPE RACKS, ANY STRUCTURAL STEEL • BRUSH GRADE CAN BE SPRAYED WITH COMMON SPRAY EQUIPMENT |
|
|
|
|
|
| Additional Products | |||||
| GeoWrap™ | |||||
|
• AN OUTER WRAP OVER RG-2400® PRODUCTS • HAS HIGH TENSILE, TEAR AND BURST STRENGTH • RESISTS ATTACK BY MANY SOLVENTS (ALKALIS & DILUTE ACIDS) |
|
|
|||
| Tank Chime Systems | |||||
|
• NON-CURING SOLUTION TO TANK BASE CORROSION ISSUES • HIGHLY CUSTOMIZABLE TO ANY SPECIFIC TANK CONFIGURATION • SIMPLE INSTALLATION, MINIMAL SURFACE PREPARATION |
|
|
|||
| VaporGuard™ Tape | |||||
|
• NON-CURING ELASTOMER FOR SUB-FREEZING INSULATION SYSTEMS • VAPOR STOP PROVIDES COLD TEMPERATURE FLEXIBILITY AT -20° • AVAILABLE IN EXTRUDED SIZES: 1-1/4” X 100’ OR 12” X 50’ |
|
|
|||
| AlumaWrap™ | |||||
|
• 4 MIL CROSS LINKED POLYETHYLENE FILM LAMINATED TO A 0.7 MIL NATURAL ALUMINUM FOIL • WEATHER PROOF PROTECTION FOR RG PRODUCTS ON NON-INSULATED PIPES AND VESSELS • AVAILABLE IN 36” X 400 FT ROLLS AND 3”X 400 FT ROLLS |
|
|
|||
| IRO™ (Impact Resistant Outerwrap) | |||||
|
• STRONG FIBERGLASS WRAP • PREIMPREGNATED WATER ACTIVATED RESIN HARDENS IN MINUTES • PROTECT FIELD JOINTS CORROSION COATING DURING DIRECTIONALLY DRILLED PIPE INSTALLATION |
|
|
|
||
| RG-CSA Primer | |||||
|
• RED PRIMER NEEDED FOR SOME ReactiveGel™ PRODUCT APPLICATION |
|
|
|
||
| RG-2400 Cleaner | |||||
|
• FOR EASY CLEAN UP FOR ReactiveGel™ PRODUCTS |
|
|
|||
| AccuTrowel | |||||
|
• PRECISE THICKNESS GUAGE • ACCURATELY APPLY ReactiveGel™ PRODUCTS • Click here to watch a video. |
|
|
|||
| updated: March 2012 | |||||